LED Strip Controller RF Remote Control (with Pairing Function) 5.5mm x 2.1mm DC Jack Connector DC 5V-24V 12A Receiver forSingle Colour LED Strip 5050 3528 2835 5630

A great solution if you have a set of LED's that just plug into a transformer with no on off switch.I can now control these from my desk. Supercool!

The media could not be loaded.  Advertised to work with LED strips but also works great with Dimmable downlights.

Good PWM (Pulse Width Modulated) rf remote dimmer for driving LEDs, this Taikuwu does not seem to get hot even when working near the maximum 6A current continuous (12A very short peak). In common with most of the others sharing this generic style it can show a faint flicker on dimmed settings.The white heat-shrink sleeving on this Taikuwu does not seal the dimmer wafer to the thin in/out leads, and the different make I am replacing with this new one became erratic after four years because of humidity from the conservatory penetrating and confusing the dimmer.Accordingly I’ve sealed the whole plug-dimmer-socket assembly in a adhesive heat-shrink sleeve. I should not have to do this, and combined with the faint flicker on dimmer settings this loses it the star.Having the M and F pair of screw-terminal mating 2.1-5.5mm connectors is useful, and these have excellent low contact-resistance to run cool even at 6A, unlike of those on some  pre-made tails .The instructions supplied with this are the most basic of all those I’ve bought, and does not mention pairing. As supplied over eight years, most of my nine samples has woken up in ‘candle flicker’ mode, which might make one think it’s broken. With all of them, selecting 100% or Pairing the remote will fix this.Pairing.Over the years the pairing software has varied what works with one may not with another. All use the same ir remote button set, just different button IDs. There are at least two possible dimmer systems allowing one to customise the remote control selection as desired.Type 1 dimmer (basic).Initialise button set as master by pressing the ‘Light’ (green button) link from the Remote in the first three seconds after applying power to the dimmer.Type 2 dimmer.Option A. To use multiple remote controls to control one dimmer, and/or to use one remote control to control multiple dimmers (very useful), please do the following:Simultaneously press the "ON/OFF" and "BRIGHT+" buttons on each remote required to pair with the dimmer within 5 seconds after the dimmer has power..Option B. To return to the original 1 to 1 pairing mode, ie wipe the above option-A choices please do the following:Simultaneously press the "100%" and "25%" buttons on the original remote control that was 1 to 1 paired with its dimmer within 5 seconds after the dimmer has power. (Make a note on the dimmer and remote which is for which when there’s more than one pair!)The dimmer module remembers the last setting, even when the 12V is removed.Button press to Dimmer functions.Red On/Standby button does as expected, when 12V is present.Note! This is another setting also remembered. Eg if it had been switched to standby and then the 12V switched also off, and later only the 12V switched on again one might think the dimmer is broken!Bright + and Bright - buttons allow ten steps of brightness.Speed + and Speed - buttons allow ten steps of ‘dynamic’ speed.Mode + and Mode - buttons allow eight choices of ‘dynamic’ modeLight will leave ‘dynamic’ modes and return to last brightness setting100% will leave ‘dynamic’ modes and set 100%50% will leave ‘dynamic’ modes and set 50%, with some faint flicker25% will leave ‘dynamic’ modes and set 25%, with some faint flickerModes might be somewhat disturbing with a big bright LED array, beware! Most of mine have these ‘dynamic’ modes.1. Candle flicker2. Breathing3. Fading 14. Fading 25. Half stroboflash6. Two-thirds stroboflash7. One-third stroboflash8. FlashThen the speed of all these can be varied from eye watering fast on the strobes to sleepy slow on the fades. Unpleasant.However all I’ve ever wanted them for is to be able to run the LEDs at about 50% brightness for most of the time, with occasional 100%.The remote uses one CR2025 lithium cell.

Only received 2 Jack plugs and a remote control. Cable not included in the sealed package

I put strips of self adhesive led lights on the skirting boards powered by a 12 volt psu and one of these to allow me to dim them. Works perfectly and allows me to dim the light to the point where we can move around safely at night but not light the whold house like a beacon

Great

Great for controlling and dimming led signs and strip.

Opened up the package and missing the cable

Schnell geliefert wurde sofort installiert für Beleuchtung an den Akkustikpaneelen. Macht was es muss

Je l'ai testé avec une petite bande led en 24V (consommation maximale 7W) et ça fonctionne très bien.Mais je pense que l'annonce d'une puissance maximale de 12A est un peu optimiste, en effet lors de mon test qui a duré environ 2 minutes, la partie où se trouve le récepteur était déjà un peu chaude (6°c au dessus de la température ambiante) et ça avec seulement un courant de l'ordre 300mA (moins de 3% de son maximum théorique) .Je ne suis pas certain qu'il survive longtemps si on l'utilise avec 12A mais pour mon usage je pense qu'il n'y aura pas de problème car je compte rester bien en dessous de 12A.

j'avais commandé précédement 2 produits identiques au meme fournisseur et ils fonctionnent parfaitement.je l'ai meme essayé sur les éclairages que j'avais doté des meme produits et il ne marche pas

Ho collegato l'interruttore ad una striscia led da 2 metri e funziona. Il telecomando funziona be e e svolge ciò che è descritto, invece il ricevitore (interruttore) agisce anche autonomamente e la luce si accende da sola quando vuole. Questo accade continuamente e anche di notte quando nessuno è nella stanza. Peccato.

Très facile et simple