for 2009-2018 Dodge Ram 1500 & Dodge Ram 2500 Halogen Headlight

Excellent replacement for 2008 RAM 1500. Easy to install and look like the originals! Fast shipper!

Project product fits awesome thank you very much guys

they look good and fit good easy to install make sure you remove the top clips from the old lights that snap into the body of the truck or remove the clip that comes from the new lights don't force it in. I removed the clips from the old lights that snap into the truck body and used the clips that came with the new lights

3 months of having them began to have issues. Have to hit the light for the light to come on after taking everything and noticing the wiring is Low Quality. Never had this issue before on different product and now 5 month mark, both lights would not come on leaving work last night. NOT A HAPPY CUSTOMER!!

The head lamps were constructed well and very easy to install. After installing the headlamps I turned them on and all is good nice and bright light. My only negative remark is the rubber gasket which goes around the main bulb was not included. Other than that, I would highly recommend this product if you want to replace your headlamps. THX

Fit and appearance are excellent for 2007 Ram 2500.

These lights look fantastic on my white RAM. Fit perfectly. Unlike what I read in another comment, these do NOT come with lights. You will need to use the old ones from your current headlights or buy new ones.

My truck is getting old (252,624 miles) and my eyesight at night is not what it used to be. So, after careful review and consideration, I decided to buy and install these aftermarket headlamp pods by ADCARLIGHTS along with separately purchased Sylvania H13 Ultra Life Capsules. This combination has worked out great cosmetically as well as functionally for my needs. Now the road is much brighter and clearer to me at night and allows me to see those pesky deer just waiting it jump out in front of me. These headlamp pods were not the least expensive, nor were they the most expensive lamp pods available. As an Industrial Engineer in the manufacturing of automotive headlamp industry for 30 years, I have to say for an aftermarket headlamp the design appears to be very close if not, the same as the original. This is why I decided to purchase and install this particular headlamp pod, along with the Sylvania H13 Ultra Life Capsules on my truck.When installing please note that it is extremely important not to handle your existing or new capsules or park/turn bulbs with your bare fingers. The oils from your hand will heat up and stress and eventually crack the glass allowing oxygen to enter the capsule or bulb causing pre-mature failure / reduce performance. I suggest installing the new capsules and bulbs to the existing connectors first taking care to handle by the base only or use nitrile gloves when handling. Then carefully engage the capsule / bulb connector to the molded features of the lamp pod until fully locked into position. Then you can engage the wire harness connectors to the appropriate capsule / bulb connector.To install the new headlamp pod, start by aligning the ball stud into the white ball socket which has been inserted into the sheet metal. Upon inspection, I decided to remove the new ball sockets that came with the new headlamp pods and re-use the existing ball socket already installed. Next press the ball stud into the ball socket firmly until you feel it engage, while aligning the lower threaded mounting stud and the two molds guide pins protruding from the housing of the lamp. Then start the threading of the 10mm nut onto the lower threaded mounting stud, but do not tighten as this time. Proceed to the two inboard mounting holes and insert and align the T30 Torx bolts in each hole and thread until you see the end of the bolt coming out of the fastener. Now press the headlamp inward again to seat all three points uniformly, (equally). Complete the threading of the 10mm nut until snug. DO NOT OVER TIGHTEN or you could break the housing or crack the housing boss. I would then proceed to the front lower T30 torx bolt and tighten until snug against the molded mount bracket and repeat for the upper T30 torx bolt. Again snuggly, DO NOT OVER TIGHTEN.The protective coating that has been applied to these lamps is intended to protect and slow the hazing process caused by the sun's ultraviolet rays. However, I am going to make it a practice to apply a spray on wax & dry spray wax to help repel rain and prevent water spots, plus help provide a clean surface, hoping that it will help preserve and prolong the protective coating.Please note these are only suggestions for handling and installation and I have no direct association with the manufacturer of these products or Amazon, this is simply my opinion. Hope this helps.

Fit great. Look good. Hopefully stay clear for a decent amount of time

The lights look great, but the rubber seals are disfigured and can’t be used in a restoration and won’t do what they are designed to do. I have reached out to the seller to replace these seals.

Very nice quality

Be aware of the locking tabs for holding the bulb in place. There is a reason there are extras. They break under stress quite easily. Otherwise fitment was a plus.

Excelentes materiales, muy recomendable