1.97 Inches Stainless Probe NTC 5 Centimeter Sensor Thermocouple DC Cord ITC1000 ITC306T ITC308S ITC310TB Thermostat Temperature Controller

Works perfectly needed a new one for inkbird I use in my 50 gallon aquarium got this and its working great again with out any issues one thing I have noticed after a few years they start to become less accurate and u can adjust the inkbird to accommodate that but I think it's better just to replace the probe so I just ordered replacements for my both of my other 30 gallon tanks with the cost to replace them it's not worth the risk of having one fail and killing all my fish

Easy to install. Use just like the original. Same quality as the original. Accurate just like the original. Good value for a good temperature control.

I bought the expensive Inkbird with heat and cool outputs for a shrimp tank that needs to be kept close to 72f. I plugged it in and it worked fine and then the temp alarm went off and I realized that the temp seemed awful high. I compared it with a couple thermometers and it was 12 deg high reading so I used the cal feature and brought it back to close and it got worse over the next week. so the original sensor must have gotten a leak or whatever. ANYWAY. i bought this replacement and the readin was .2 off from the thermometers so I just left it. The unite does allow to correct for tenths as well but I did not bother. well worth it and I bought the right product. I have the heat feeding a heater set to 75 so it cant go over fed but the unit set to 72, the cooling feeds a small aquarium fan with a neck to blow air over top. Works perfectly....

Works great to replace probably any Inkbird temp probe, white and black wire inside. Comes with a female connector to make any Inkbird probe replaceable

Has worked OK for a month now. I did calibrate a tad. Not waterproof, but another similar product is (if you search for it). The water-proof one lasted about 4 years in a hot tub.

Bought this to replace the wired in probe for my Inkbird 308 and was very easy to solder the new connection in with a woodburning pen. Take about five minutes for the entire job and now if it goes out again, I can simply unplug it, and put in a new replacement.

Worked great for 2 Inkbird duel stage controlers. This comes with a socket to solder into the controller that upgrades it to a quick plug in probe so it plugs in like headphones. Easy to solder in just match the black and white wires. My fish are happy again!

I bought this probe to replace the previous probe which did the exact same thing. Here's what it does, works fine for about six months, temperature set to turn the aquarium heater on at 72 degrees and off at 73 degrees. Running a 150 watt heater. After about six months, suddenly the low temperature alarm is going off, emergency, fish cold, help! Glance at the submerged thermometer, it's reading 78 degrees, way too hot! That's what happens, the probe starts reading wrong, thinks the temperature is down, turns on the heater, probe doesn't register the temperature, heater stays on, fish die. Fortunately, I learned my lesson from last time when I was using an old heater that had the thermostat stuck on. This time I had a new heater with the thermostat set so it couldn't cook the fish, even if the Inkbird got stuck on again. This is the second time. First time could have been a fluke, this probe is only six months old. I'm done. I liked the Inkbird because I could hang it on the wall for an easy readout, but this thing has bit me twice. DO NOT BUY.

Nice long cable. Bought this to use on my remote wifi temp monitor ( https://www.amazon.ca/dp/B09YTZQMM6?psc=1&ref=ppx_yo2ov_dt_b_product_details ) In the temperature range most important me which is from 28C to 45C the accuracy which i confirmed with 2 other calibrated temp monitors was DEAD ON .

La utilicé para reemplazar una sonda averiada de un Inkbird itc-308 wifi y funciona correctamente. Trae el jack y la sonda.

Excelente compra. Las recomiendo

Still works to this day, lovely - just what I needed.

Looks good have not tried yet waiting for socket