Intermatic FD60MWC 60-Minute Spring-Wound In-Wall Countdown Timer Switch for Auto-Off control of Fans and Lights, White

I have an older mobile home and the one that came with the home failed. I bought this and it works great. Easy to install

Timer description matched the product exactly. The instructions list three different models of this timer switch. The difference between models only appears to be how the wires connect. The timer came with two screws to mount to the electric box, and two screws to make the wire connections. It also came with the timer plate and nut to fasten the plate, and the knob. Wire connections were easy, although you have to look closely to see the molded in "line" and "load" markings. Basically its black wire feed to the line connection, then the fan (or other device) to the load connection. Make neutral to neutral (white) and ground to ground (bare copper) connections as typical of any wall switch. And like the description says, "Supplied with a molded white time dial plate designed to fit either toggle or decorator style switch plates ". That means it only comes with the timer plate, but not a switch plate. (the time dial plate is the rectangle with the time marks on it. It fits a standard wall plate with large rectangular opening).It works as it supposed to and seems accurate with its timeing. The knob was quite hard to turn the first time, but after a few days of use it has loosened up in both directions. The clicking noise of the timer can't be heard over the sound of the whole house fan that is directly overhead. With the power off, I noticed the timer is quiet enough to use with bedroom ceiling fans (which I am considering doing).All in all, its appears to be a good buy. Much less expensive than the choices at the home centers, and at 6 hour timing it is just what we needed for our attic fan.Update: The Master Flow whole house attic fan came with a rocker switch with Off, Low, and High positions. When the fan was installed, I put in a two gang electric box (double box) because I knew I wanted to add a timer. But now with this timer installed, the rocker switch Off position was no longer needed, plus finding a cover plate with the decorator opening on one side for the time, and a custom size hole for a rocker switch on the other was impossible. So I tossed the rocker and got a regular 3-way wall switch, and wall plate with the regular toggle switch opening on one side, and the decorator opening on the other. Then I wired the power to the timer, then to the 3-way. So now the timer functions as the on/off switch, and the 3-way toggle is just High and Low. Much better functionality, and nice clean wall switch plate.The whole house fan I have is a 30" belt drive model that is rated at 4 amps, so this switch is more than sufficient.BTW, the timer switch specs/ratings are:Resistive: 20 Amp, 125 VAC, 50/60 Hz10 Amp, 250 VAC, 50/60 Hz10 Amp, 277 VAC, 50/60 HzTungsten: 7 Amp, 125 VACMotor: 1 HP, 120 VAC, 50/60 Hz2 HP, 240 VAC, 50/60 HzOperating Temperature: -40¢ªF to 104¢ªF (-40¢ªC to 40¢ªC)Style: Can be used with decorator and toggletype switch platesDimensions: 2.79" H x 1.6" W x 1.19" D

I wore out the first two of these I've owned in my life prematurely by turning them backwards to make them stop. Don't do that, and buy the "hold" feature if you might ever need on/off functionality. I like the idea that "holding" the fan on while the shower is running, then timing the fan afterwards, saves some wear on the spring, as opposed to winding it twice.After an exhaustive search of the digital and analog options which were on the market in 2019, I bought more of these. I wish I had bought even more at that price, although I expect I will be good for a decade. I don't like the failure modes of digital timers.So, if you don't wear out the timers by turning them backwards, the plastic knobs will not last as long as the timer. I'm sure some cost cutting was involved, but this wasn't a particularly recent change, as one of my timers is seven years old. At the non-bulk price of the replacement knobs, I have bought milled aluminum guitar knobs with set screws for a slightly bigger shaft (1/4" or 6mm instead of 3/16").After putting a tiny dab of silicone grease on the set screw threads and tightening them up, I did not feel any need to pad out the shaft, they were rock solid and fit almost flush with the faceplate. 1" diameter is easy to grip and matches the faceplate. I avoided models (some of which were more expensive) with plastic inserts, especially "universal" ones with both splines and set screws. The minor annoyance is that the arrow is 180 degrees off - you want the arrow, if any, to be inline with the set screw. I might fix that with a Sharpie some day. I expect these to outlast the timers.

I just purchased this switch and installed it on my bathroom fan so that I could leave it running for a while after showering. Previously we have been doing this manually, but I usually leave the house right after showering in the AM and so the bathroom was getting mildew. Before buying this switch I bought an electronic timer to install however it turned out my electrical box did not have a neutral connection (as whoever installed my light/fan unit only ran the hot down to the switch box), so using this mechanically (spring) driven switch was the solution.In general I would say the switch is reasonably well made. I see these same brand switches all over the place so they are extremely popular. It was annoying during the install to get the switch lined up in exactly the right spot so that the decora cover plate fit over it. I ended up installing it once with the switch not tightened into the electrical box (so it could move to the right place when I put on the cover), but then once I put the knob on the switch I realized it felt pretty loose and so I went back and tightened down the screws to hold it to the box (just guessing what the alignment should be). Really, the time dial piece of plastic is pretty annoying to install outside of the switch plate - I think they should just build the time dial into the switch (but I think they are riding the fence trying to make one part that works in "classic" light switch face plates and decora style ones.I do have to agree with another commenter that the press-fit dial handle on the front was very hard to put on (plus you don't really know how deep it is supposed to go and when you should stop applying force - breaking the switch is a real possibility). As stated above, I installed the switch twice trying to get the alignment right and pulling the dial handle off was very difficult (resorted to prying with a screwdriver which could mar the switch or the faceplate). This is where I would consider it to be poor quality. (hence only four stars)I also need to call out the instructions from in the box and also posted on this product info page as being poor quality. Specifically, from what I can infer, they offer at least three versions of this switch: Single pole single throw (this one I bought and wrote the review of - it is your basic light switch), single pole double throw (3 way switch), and double pole double throw (i.e. 240v applications where you need to break both "hots"). From what I can glean from the instructions in my package and the wiring examples on this site, the single pole double throw switch actually can do a lot more than that. It seems to have two current paths through the switch, one of which the current is broken when the switch is "on" and one that is closed when the switch is "on". By wiring this switch in different ways you can use it to turn something off during the timed interval, or use it in 3 way situations. They really badly need to provide a series of diagrams that shows the electrical operation of each type of switch rather than just providing specific wiring examples (which they don't explicitly tell you which type of switch you need to buy to accomplish).This is the right switch for a lot of use cases, but I wish there was a slightly higher quality option, better documentation, and a little easier installation in decora style faceplates.-Eric