Moen Arbor Motionsense Wave Sensor Touchless One-Handle High Arc Pulldown Kitchen Faucet Featuring Reflex (7594EWSRS), Spot Resist Stainless, 3.63x26.63x14.25

رايع جدا

Bought this to replace a less satisfying Price Pfister kitchen faucet in a new house. We had an similar non-motionsense Moen faucet in our old house, which we liked. Pros: - We really love the motionsense. It works well. Not having to use dirty hands on the faucet is an advantage. - The Moen is better than Price Pfister. We have a Delta faucet in my dads house - the spray head on the Moen is better than the Delta, specifically the spray pattern is better and the faucet automatically switches back to stream when turned off, which I like. - Installation is easier than the regular model since you don't have to run the hot and cold water lines up to the faucet (they go the flow control module). Cons: - The water flow is less than the non-motionsense version. I would guess about 2/3's of the non-motionsense version . That being said, we still definitely prefer the motionsense version - thus 5 stars. - Occasionally the faucet will activate when not intended if your hands pass close the lower sensor. The function of this sensor can be turned off if desired. Observations & Suggestions: - The guts of this faucet is the battery powered flow control module which you mount somewhere on the back/side of the sink cabinet. The hot/cold mix and on/off/flow rate are all done by this module. The handle on the faucet only sends an electronic signal to this module. This is elegant. If you have plumbing problems (faucet drips etc) all you have to do is replace the module which is probably easier than tearing the faucet apart. Moen is good about standing behind their products and hopefully this module has a good service life. - The module comes with a battery power pack with an option to order a plug-in 120 volt power supply. The faucet will not operate (no water at all) without power. I think the battery power supply is a better option because the faucet will still operate if your house loses power during a storm. I assume the faucet will blink and otherwise notify you when the batteries need to be changed. Changing the batteries is a pain because you need to clean out the bottom of your cabinet to get to the back to change the batteries. If this is a problem YOU NEED CONSIDER THE SUITABILITY of this faucet. - The water hose that runs to the faucet head has a marker tape where the weight is supposed to go. Our sink is large and the faucet head would not reach the edges of the sink with the weight at the 'recommended' location. I moved the weight further down the hose with very satisfactory results.

Excelente producto. Los sensores son muy útiles. Incluye 6 baterías y según el instructivo duran hasta un año. Tiene todo lo necesario para instalarse y no requiere de tornillos ya que se el centro de control se adhiere a la misma mezclsdora y la caja de las baterías incluye una etiqueta que pega a la pared. Solo hay que considerar que las mangueras son de 3/8’ y no de 1/2’ como normalmente se acostumbra en México, pero se pueden cambiar las válvulas que se conectan directamente a la tubería y se consiguen en cualquier ferretería.

LOVE this faucet! Very functional with smooth operation not only with Temperature adjustment, but Pull-down. The latter retracts easily on its' own and the spray option is perfect for rinsing items and sink. The finish is beautiful and matches all the other stainless appliances. A great looking but very functional addition to our kitchen. Highly recommend.

Great faucet with no problems mentioned like other faucets as far as splashing. This is perfect. I love the high arc and I put it in my 30 inch kraus 70/30 sink and it looks wonderful together. I have a very small kitchen and it does not overpower the kitchen at all. We just remodeled our kitchen completely and between the sink and the faucet it gave our kitchen a more modern look exactly what we were going for. There is absolutely no splashing and it goes between spray and flow with a simple touch of a button without have to turn the water off. I also like the finish as it leaves no fingerprints. The sprayer when used glides so easily and retracts smoothly. It took me almost 2 weeks to decide what faucet to buy. I read all the reviews (which helped me greatly) before deciding. I was ready to buy a faucet at Costco until I read about the bad reviews that particular brand received. It arrived very quickly from Amazon. I ordered it on a Friday and it arrived on Tuesday.

12/28/19 Update - I have had to replace the hose and the valve seal again this past year. I keep the extra parts and the tools in it's own box, so when there is a problem, I fix in 15 minutes and call Moen for the replacements. From a reliability point of view, this unit is bad. The performance and appearance are great, so I still score a 3 from my situation. For somebody that needs to call a plumber and doesn't understand how to deal with leaky faucets to make sure there is no water damage, this is a risky unit. 6/2/18 UPDATE - in 2016 the hose started to leak, squirting sideways. It is a braided plastic hose and probably fails for most after 3-5 years. Moen again sent me a replacement which took me about 30 minutes to install. For last two years the unit has been ok. Summary, good unit. But will need maintenance every few years for either the hose or the o-ring seal on handle. As long as Moen supplies the parts, it's an ok deal. 12/15/15 UPDATE - stable now over the last year. I suspect the leaks were related to the tightness of the Oring retainer ring. Instructions said to go finger tight plus one half turn. I suggest finger tight plus 3/4 to 1 turn. I like the unit, would buy again. 12/29/14 UPDATE - Well, after another 7 months, developed a leak again that went from a drip to a flow in a couple of days. I had a spare oring that I had purchased in July, but it leaked! Moen delivery will be a week, so I purchased another 2 day delivery replacement valve from Amazon. Also added some plumbers grease (not included with replacement valve) and a 13/16 socket kit to more easily remove the valve. So I am about an hour and about $40 into this repair. I will order another freebie replacement from Moen for the next time, which is likely to come in 7 months. I am wondering if it's the high mineral content of the water here? Dropped my rating to 4 stars. 7/23/14 UPDATE - Well, after only 7 months, developed a leak that went from a single drop to 3 drops per second in less than 3 days. Disappointed. I called Moen since they have a life-time warranty and they sent me another cartridge with no charge. You can buy the same cartridge on Amazon for $17. Search "Moen 1255 Duralast Single Lever Cartridge." Took me 10 minutes to replace. I had to use my own 3/32 allen wrench as the wrench they sent with the cartridge kit was too short on the short end, and too long on the long end, to fit in the space to turn the set screw. No more leaks. So generally the good customer service and ease of replacing the cartridge saved their rating, but still, 7 months is not a long time. We will see how long it lasts. INITIAL REVIEW - Hope the designer got a nice bonus. I particularly like the feel and breakaway friction of the handle. Straight forward to install. Quality construction with very consistent stainless workmanship. Just looks and feels classy. This is the most deserving 5 stars I have ever given. Straightforward installation. We'll see how durable it is - I'll check back in with a comment in 6 months. For those looking for it - purchase a Moen 141025 O-Ring Kit for 2.2 gallons/min. Amazon sells this too. (However, side notes to Moen: 1) when I pay $300 for a faucet (that comes with the reduced 1.5 gallon/min flow aerator), I don't understand why you just don't included the 2.2 gallon/min flow aerator option in the package and save me the $10 and time it takes to separately purchase this 25 cent part. 2) Come-on guys, the cover plate is used when there are 3 holes - so use one of these extra 2 holes to lock it down. It is extremely difficult, if not outright impossible, to secure the cover plate from rotating using only the center hole - and the gasket extrudes out the center and not the sides if you try to tighten it down. A well designed product is matched with an incompetent cover plate design - at least you didn't make me purchase it separately like the aerator)