Camco Power Grip 50 Amp Replacement Plug - Head Attaches to Existing RV Extension Cord - Features 50 Amp RV Plug (NEMA 14-50P) with Ergonomic Designed Handle - Rated 125-250V/12,500W (55255)

The original one needed to be replaced and this was the perfect replacement. Easy to install. -Lots of You Tubes :) We are full time RVer's and have been using this for 6 months since installing and it's still working great! Recommend and would buy again!

Excellent replacement for one that burned and melted. Works great, doesn’t get too hot. We are using it on a Keystone Montana 3725RL 40ft fifth wheel camper. No assembly needed. Seems durable. It’s waterproof so far (lol). We’ve had no problems with this plug.

Haven’t used it yet but looks to be of good quality and parts look like they are rated for 50 amp load.

Makes the work done but the plastic its cheap not that high of a quality but good to have for an emergency easy to install and it fits good terminals makes good connectivity

Installation of the cable was easy. Though in my cable the ground wire is uninsulated. I had to use some heat shrink wrap to insulate the ground and steer it clear of the other prongs. Note that this cable isn't weather proof.connecting and disconnecting it have been easy and without incident thanks to the built-in handle. The plug has a removable piece that let's you use cables of different sizes.

My existing plug was worn and ready to fail. Watched a YouTube video and followed the instructions to the letter. Now, I have a fully functional power cable at a fraction of the cost of an entire new one. If you are in this situation, I highly recommend.

Having a handle attached to this plug end makes this a great product. It's a well thought out, well manufactured/designed product. This plug end was attached to the end of a twenty-five foot SOOW, 10/4 cable to be used as a jumper between an emergency generator and an electrician installed, 50A RV receptor on the side of the house next to the electric service box for easy service disconnect. Plug ends this hefty are hard to pull out, especially if inside an all weather outlet cover box where there's little room to maneuver your hand. With the addition of the handle, the plug end is much easier to remove. This is a good thing. :) The assembly takes a bit of time at the project table as the leads have to be cut and stripped to specific lengths specified in the directions. It's not a difficult task, but it is a bit of a time consuming pain to make sure it's measured and done right. The more care one takes in cutting and stripping the cable wires to well defined direction specs, the more easily the assembly will go. Tip: When assembling the cable strain relief collar, add a dab of latex/siliconized caulk to the inside and outside of the strain relief collar as well as the small gap between the strain relief collar and the plug body. This will help keep snow and water out which will effectively make the plug end more water resistant. Doing so also gives the plug end a more finished look/feel. Warning: Adding the caulk in this fashion won't make the plug-end "waterproof." A cable end of this kind will be used out in the weather and considering the amps this plug-end is designed to push, "more" water resistant is a good thing; peace of mind. I found this product to be the top dog of this group and for those with a "Prime" membership, two-day shipping is included. At current gas prices, this eliminates the need to drive to a RV or hardware store hunting for an item of this kind.

I don't write many reviews but was most impressed with this plug. #1) the plastic is sturdy, no concerns with durability. #2) The handle makes pulling it out of the socket a breeze. #3) the cable retention design allows for various sizes of cable through a unique design. #4) The wire connection allows for excellent contact with the blades. #5) I measured the temperatures of the socket under about 38amps of load and only measured a couple degree rise. I saw some photos of failed sockets with folks charging their Tesla's. That is probably closer to the rated 50A but can't imagine an issue with that if you get good wire insertion and contact. Finally, I saw some comments about how it was difficult to tighten the screws. I attached a picture showing how the blades remove so that you can get good torque on the connections. No regrets, bought two of them for generator connections.

Seems to be the best NEMA 14-50 plug on the market. Quite sturdy and easy to wire. Quite ergonomic for a plug that is usually notoriously stiff to insert/remove. I've bought a few already and will likely buy more. The only issue is the price has gone up.

Muy buen a calidad y es una buena instalación en mi garage

Well suited for 6/3 wire, plenty of room inside the housing and you can easily take the terminals out to secure the wires. Feels sturdy and much better quality than the other cheaper 14-50 plug you can find, well worth it.

This is a plastic mold in two pieces. Not the greatest quality but if it's used occasionally and with care, I am sure it will last a few years. Connecting the wires is easy and fast, I use it with an 8 AWG SOOW cable.

Employé pour remplacer une prise femelle par cette prise mâle sur un fil de génératrice 50A