VFD 220V 4kw 5HP

Take a chance, and take your time installing. The first one I received did not light up, so I was a bit concerned. But I have had good luck so far , so I opted for a replacement. The replacement came the same day and it did not fail to perform. I have been researching VFD programming for 3 phase machinery for a week. After changing every hertz value to 60, I powered up the spindle and watched it slowly creep into a full rotation speed and upwards to the fired speeds. The initial install is basic , I have not wired in my momentary switches for direction and stop. I will also add an external tach on the machine. But that is in the future. All in all it was worth buying, my machine is only running a 3/4 hp 3 phase motor. I will eventually need something bigger , but for now this is great! Compared to the sounds of machinery I think the VFD is quiet

I'm using this for a belt grinder. I thought it had fried one day. Saw a big spark at the control box and blew the breaker in my panel. But, it was my own fault. Either the wall switch or the control box got some grinding dust in it and that's what caused the problem. I reset the breaker and all was well. I then got a bit wiser and put a ziplock over the top of the switch and the panel to keep grinding dust away from them. It's been working flawlessly for 4 or 5 months now. Point is, the VFD is great. I'm running a 1.5HP 220v Hallmark 1800 RPM motor. I over-speed the motor by 50% (90 on the frequency dial) to get 2700 RPM. Supposedly, I should be able to turn it up to 120 or even 130...but I'm pretty happy where it's set now. FYI, I don't think I had to change any settings to initially run with a frequency cap of 60. So, very easy to set up. The wiring space is a bit limited. MY tip is: Don't use wirenuts - use WAGO connectors. They fit much more easily.

I used the AT1-1500 2HP unit to power up a 1966 Bridgeport Series 1 1 HP mill. The motor was originally wired for 440 VAC 3-phase. I only had 220VAC 1-phase in my barn. I reconnected the motor leads for 220VAC. The unit worked flawlessly in converting 1-phase to 3-phase. I am an engineer and have installed many VFD drives. The instructions are somewhat difficult to understand. There several videos online that are helpful and the seller's tech team responded to emails within 1-2 days. There are a few things that the unit does not like. Most Bridgeports have a reversing drum switch mounted on the motor. My original intent was to power up the VFD with the run command at the same time. The VFD goes through a brief self diagnostic routine when it is first powered up. Calling for a run command at startup caused an Error 1 display. When I added a separate Off-Run switch, the unit functioned without error since there was an inherent delay between powering the VFD and switching it into run mode. Secondly, the unit did not work with the reversing drum switch. After switching the VFD to run, I actuated the drum switch and the unit tripped out on overload (Error 2). Positioning the drum switch in forward or reverse before commanding the VFD into run eliminated this. I removed the drum switch and replaced it with an aluminum junction box from Amazon. I changed the Off-Run switch to a 3-position Reverse-Off-Forward switch and wired it to terminals X4 and X5. The motor worked perfectly. I set the minimum Hertz (P07) to 60.0. Running an older, non-inverter duty motor at less than full RPM can cause it to overheat. A replacement motor is $1500. I am content to change the belt drive step pulleys. Lastly, because the AC sine wave current is generated by modulating pulses of DC current, a standard Amprobe meter will not read the correct input or output amperage. But, the motor amp draw can be displayed on the control unit.

THE GOOD: - It worked when powered up! - The parameters were preset pretty decently for my drill press. - It is a simple VFD with few settings to worry about but still has the basic features needed. - Far less expensive than big name VFDs. THE BAD: - It is not safe for facemounting without a box/enclosure. This was a big deal for me. I was working with 10 AWG SOOW and my older unit (a Delta) was set up to accomodate with appropriate cable clamps meeting code so the individual conductors were enclosed at all points where the outer jacket was stripped. In order to safely fixt this problem, I had to mount the VFD inside of a UL listed electrical enclosure. - The wire terminals were too small for the appropriately sized conductors. Could I get #10 wire in place? Yes, but it was a job. The terminals have a wire clamp similar to what might be found on a NEMA plug, but it was VERY difficult to get the wire into the clamp without a terminal end. As others noted, the terminals are not big enough to accomdate a forkl terminal much less a ring. I ended up stripping the jacket and soldering the tightlest twisted conductors so no loose strands would create an opportunity for arc or short. THE UGLY: - I remain apprehensive given the comments others have made about the unit failing soon after installation. Only time will tell but it would be nice to have a little confidence in the product.

This vfd is working great to drive my original motorized power feed on older Bridgeport mill. The only reason I deducted one star is that I’m not sure how long it will last. It does not have a cooling fan, but does have an oversized aluminum heat sink. It will mounted inside a fairly large box with a name brand vfd that powers the mill’s motor (this one has a cooling fan). However, I have installed a computer cooling fan in the bottom of the box with outlet in the door (similar to “Clough42” on YouTube). This should help with cooling both vfd’s and extending the life of both. For occasional use, I think it will be fine. If I needed one for regular daily use, I’d probably step up to a name brand, but for hobby use I think it will be ok. Only time will tell. Btw, I will probably order another one to run a floor model 12 inch grinder that is 3 phase.

Me funcionó tan bien que compre 2 piezas. Lo ocupe para alimentar a una fresadora ya qué sólo cuento con luz a 120 volts. Alimento a 120 volts y me da de salida trifasica 220. Muy fácil de programar se los recomiendo ampliamente. Excelente precio calidad

Error 1, incluso sin motor conectado.