NY Brew Supply W3850-CV Super Efficient 3/8 x 50' Copper Wort Chiller

This chiller is well-made and great value for the price, compared to similar models available at higher prices. I have always used a counterflow chiller, but needed an immersion chiller to be able to the control the wort temperature for hop additions and steeps at specific temperatures. It works perfectly for that as intended. Everyone's equipment is different, but I was surprised to find that chilling with this is faster and significantly more efficient than my counterflow chiller. I wish I'd bought this years ago! The fitting and hose that ships with this are of good quality, and the amount of hose is appropriate for most possible set-ups I can imagine, unless you have a long way to go to connect things. I wash this carefully between uses, and sanitize by submersing in the kettle for the last part of the boil. Please be careful- even though I blow the water out after each use, there is always some residual water in it, and the first shot of water through it will be insanely hot, and can create a jet effect enough to blow the outgoing hose out of whatever sink or bucket you run it into. I learned this the hard way when it rocketed out of my sink and blasted me from head to toe with a shot of boiling water. Secure the hose well, or let the first flow of water through it carefully! This is not a fault of the chiller- just my failure in managing some basic physics, so please learn from my mistake.

I am really happy with this. Novice brewer, have only used it once, that being yesterday. For an assembled apparatus, it cost about what 50' of copper tubing would have cost me. Here are some details: No, it really has no packaging to speak of, but arrived in perfect condition. The stems (inlet and outlet) may be short, but if you are worried about leaking over your wort, gently bend the whole neck so they are nowhere near the edge of the pot. Furthermore, if you are worried about leaks, get a couple more hose clamps - use two per connection (alternate their orientation) and importantly, heat the hose gently before sliding it on the copper, so when you tighten the clamps, they rally crush it down. In use, I found it cooled faster with a more moderate flow of water (which saves water) and also agitating the wort with the cooler helps tremendously. Up and down, side to side ... in fact .. if I let it sit still, the outflow would be cooler, yet if I moved it around, the outflow tube would get hot quickly. That is the heat from the wort going away! I didn't time it, as I was too busy doing it ... but it felt like 5, maybe 10 minutes at most to cool below 80 F with a full 20qt. kettle. One other thing ... I sanitized my cooler with Star-San prior to use, rather than putting it into the boil 10-15 minutes before the end. Reason I did this was that I had my cooler rigged in the basement sink (where I had plumbing that would work) and was doing the boil upstairs in the kitchen. Eliminating dangling hoses and complication during the carrying of a full kettle down stairs seemed like a wise move. Other than the use of some Star-San, I don't see what the big deal is with that, and it actually seemed to make my life easier (and avoid preheating the copper, which is just more mass to cool) I'd buy this again in a heartbeat, and am sure it would cool larger batches quickly too, if I move up in size. I don't think I'll have to though!

Lets start with how well-made this chiller is. When I saw the price i was worried it was going to skimp out on build quality, but that is NOT the case at all. Coming from a counterflow chiller and having used copper in the past I knew what i was looking for. I wanted, no needed something that would cut my chilling time down, while being much more efficient. I have this hooked up to a pump that circulates the water at 2GPM and have it circulate through ice water ( bayite BYT-7A014A DC 12V Solar Hot Water Heater Circulation Pump with DC Power Supply Adapter Low Noise 3M Head 8LPM 2.1GPM ) This has brought my 10gal chill time to under 15 minutes, and 5gal to under 10. That's wicked fast The hosing and connectors are good, They do clamp on, and if that bothers you for cleaning, you'll want to take note. Ample length of hose for every set up that I've ever seen, and the hose connector. As with every piece of brewing equipment, wash this carefully between uses, and sanitize. I do so the latter by placing in the boil for the last 5 minutes. the stainless cleans better than copper does, and doens't pose the risk of pitting out and blowing out ruining your hard worked wart. Keep it clean and i can't see how this doesn't last you for many years to come!

There are better, more efficient emersion chillers out there. They cost more and are probably worth the price if you feel a super-fast "chill" post-boil is a critical step in assuring your brew is as good as it gets. As an all-grain brewer for 4 years, I don't perceive value in chilling the wort to target temp in 10 minutes vs 60 (I am busy doing other tasks and don't notice the time). Pro brewers would certainly have a more valid opinion and this might be a false assumption. Anyway, this unit is way more efficient than the 25 foot loosely coiled copper chiller I threw together early on. It is rigid, well constructed and easily 4 times as efficient compared to what I was used to. All in all, it is a great step "up" for speeding my brew day along.

Having just started home brewing a couple of months ago, I wasn't sure if I really needed a wort chiller. After using this one, I have no idea how I made my first batch without it! This wort chiller is extremely well made, with extra long tubing to give you the flexibility to use it either in the sink, on a counter or on the stove. The included hose clamps help keep the tubes connected to the chiller. The copper is a very high quality tubing that cools hot liquids quickly. It took five gallons of wort from boiling to 70 degrees in about 15 minutes. It took me almost four times that long to cool it in an ice bath on my last batch! Only two minor gripes: first, an extra hose clamp would be good, as one of the hoses had just enough of a gap where water could spray out and into the wort unless I held it (not a huge deal, but still inconvenient). Also, the fitting is a 3/4" female hose fitting, so you need an adapter to hook it up to a faucet. I really wish they would have put a 5/8" male fitting on it instead, as the adapter is tricky to find. Having said that, you could go to your local hardware store and fix both issues for around $10. Other than those minor, but fixable issues, this is an outstanding product and a must for anyone who is serious about home brewing!

This thing is designed quite well to chill off that boiling hot wort that just consumed 1.5-2 hours of your Saturday afternoon. The beauty of this device is that it decreases the amount of time that it takes to chill the wort by 3x-4x; it usually took over an hour in the ice bath in my sink to chill 5 gallons of boiling beery goodness to a yeast-friendly 75 degrees. My first attempt using this device cut that time to 14 minutes. The chiller itself is well designed and was well packaged for shipping, though as one would expect, there were the old knick and scratch of the soft copper, presumably from shipping. I scrubbed mine well before the first use and, as the instructions say, be sure to use something to remove the oils from manufacturing. The hardest part about this chiller is getting the tubing provided to fit onto the chiller and the garden hose nozzles. I had to use a pair of needle-nose pliers to stretch the opening of the tubing, after soaking in boiling water to soften the tubing enough to force it onto the chiller and nozzle. Once sufficiently in place, though, I clamped all the tubing down and I did not have any leaks on my first use. Protip: have a plan for the water that comes out of the other end. I just let mine run down into the street, but the closet environmentalist in me said I should use it for watering plants or filling the washing machine or something. Whatever, I'll hug a tree next time. With the size of this chiller, it should make short work of cooling off any boiling brew kettle 10" or greater in diameter. Time will vary, of course, with the temperature of the water that comes from your garden spout.

This chiller works great. It chilled my 5 gallon batch (more like 4 gallons after boil loss) from boiling to 70F in about 10 minutes. I'll never go back to doing ice baths again! A couple tips: Get the plastic tubing nice and hot before sliding over the input and output posts to ensure the plastic tubing is flexible enough to do so. It's a tight fit otherwise. Once on and secured tightly with the clamps, connect to a hose/sink and test it out. Got a good seal? If so, toss the chiller in your boiling wort 15 minutes before flame out. It's going to get hot and the hot water left in the chiller is going to shoot out of the plastic tubing. Be careful! Now that the chiller is hot and the plastic tubing is too, crank down on those clamps even more to get a tighter fit and ensure there will be no leaks. I originally skipped this last step, hooked up the hose and sprung a big leak. Really hope I didn't infect the IPA I brewed yesterday! Take my advice or you might be sorry. Overall, I love this chiller!

I purchased this wort chiller last year and used it for the first time a few days ago. It was a disaster. I connected the plastic hoses to the copper lines but they don't supply two hose clamps. The inlet/oulet lines are too short and the clear hose bends when placed in my all in one brew machine. The worst part is the super cheap brass hose connection. I connected my garden hose to the brass fitting and turned the water on. The plastic tube was bent since the copper lines are too short. The water from the garden hose leaked into my wort! Then the brass hose fitting started to leak. I went to hand tighten it when it completey popped out of the brass ring spraying water all over my house. I pushed the cheap brass pieces back together but they continued to spray water. I wasted lots of water and time trying to cool my wort. It's likely the wort I spent 5 hours making is destroyed. I also paid $42 for a 5 gallon Beligum Beer Kit. What a waste. $75 for a coil of copper and cheap brass fitting. I knew I should have made my own and I'm a plumber! It's too late to return this item. I'll have to buy a quality brass hose connector and extend the copper tube to be able to use this item.