H2o Kayak Canoe Anchor Trolley Kit

Delivered quickly, and well packaged up. Pack contains decent instructions, but to be honest, I didn’t really need them. Trolley is simply to fit, and comes with everything you need….(thank god for the rivets!!). Due to limited access at the stern of my kayak, my only real option was to use the rivets supplied, and have to say, they are solid. All-in-all, really impressed with this product, especially for the price- I would definitely recommend!!!

This is the second one I've bought and they are decent quality. Does as it says and all the pieces are there. Bolts if you can reach the inside of the kayak and rivets with rubber washers if you can't. I always add a bit of silicone over the rivets as im not sure if they will let in water but their probably watertight.

You are reading this because you fancy fitting a trolley system to your yak or maybe upgrading. Look no further. This is a good system, easy to fit and with clear instructions. My technical knowledge is very basic and I had no difficulty fitting this. I wish that they had supplied well nuts instead of bolts but that is just a personal preference. I used the neoprene shrouded pop rivets for the pad eyes and they worked fine . I had a couple of 10 mm well nuts spare so used them for the zig zag cleat as access was easy from the deck hatch. If you do not have a pop riveter then you will most likely have to buy well nuts as the access for bolts in the forward and aft fittings will be problematic. Probably as cheap to buy a pop rivet gun as they are only about £6 and they are a lot quicker to use. The fittings are all of good quality and should last well. Tensioning the cord is pretty straightforward but I plan on introducing a bungee in the fitting at some point. Probably around the forward pulley to maintain the tension and allow for any wave jerks when anchored or using the drogue. If there had been well nuts supplied I would have given this 5 stars. I have dealt with H2o on and off for a while now and I have always found them to be a good company with advice as needed.

Bought it for my big game 2 and fitted it with no problems the rivets and bolts hold the kit solid and works well Quality parts and well worth the money remember and add sealant to the fixings to ensure they are watertight

This going to make my kayak alot safer for me

Very nice kit for the money. The kit is easy to fit, I used both the bolts and pop rivets when fitting it to my Prowler ocean kayak it's not going anywhere. watch the youtube video for a fitting guide. http://youtu.be/SyseldPCmLo

Simple and easy to fit, completed in 10-15 minutes. Used the trolley kit several times now, certainly been put through its paces as I anchor up in strong fast tides off of the Isle of Wight . Excellent for little money

good quality kit

I installed the trolly on my exposition sea kayak.

Il prodotto è di buona fattura e di facile installazione. Il test definitivo lo avrò nel momento in cui il prodotto sarà utilizzato al mare (resisterà alla salsedine?) Spedizione nei tempi previsti

Habe damit mein Sit-on-Top-Kajak zum Angeln ausgestattet. Funktioniert super und mit minimalstem Aufwand kann ich mein Kajak nach Wind und Strömung ausrichten! Finde ich super praktisch und kann ich jedem empfehlen, der sein Kleinfahrzeug an einer bestimmten Ankerposition halten will! Montagematerial ist alles dabei, insesondere Schrauben bzw. auch Blindnieten (als Alternative für unzugängliche Stellen am Boot, wie bei mir am Heck zum Beispiel). Den Klotz für die Schnurbremse nutze ich auch zum Verzurren des Ankerseils. Den Ring zur Durchführung des Ankerseils habe ich gegen einen Edelstahl-Schnapphaken mit Wirbel getauscht, damit kann ich das Ankerseil ohne langes Durchfädeln einfach einhängen. Das Trolling-System ist ein Must-have für jeden Kajak-Angler :-)

Though all the parts are not the same, this was much cheaper than the popular brand, is easy to install and will work just fine. I could not buy the individual parts cheaper than this kit. It includes everything that you need, except for a drill, knife and rivet gun (or screwdriver and pliers), including both SS screws/bolts and black rivets with washers. The rivets do not insert easily into a 3/16” or #11 drilled hole, which is probably a good thing as it results in a tight fit. Other than a slightly larger diameter and the gasket, the included rivets are virtually identical to others that I bought from Amazon at the same time. The connecting ring is made of the same plastic as the pad eyes, not steel. The head of a rivet gun will not fit inside the zig-zag cleat to set the rivets. I slipped a metal cylindrical spacer over the rivet nail which allowed me to use the rivet gun (see photo). A similar spacer could be easily made from a BIC pen or a small piece of copper or brass tubing. Or, you might be able to use a screwdriver blade as a spacer between the rivet and rivet gun. I put silicone sealant beneath the rivet heads and under each pad eye and the zig-zag cleat. I also added small bungee cords at each end between the pad eyes and the small carabiners to keep the trolley line taut and to provide some give. I added another SS mini-carabiner (from WalMart) at one end of the rope where it attaches to the ring. This way, I can easily unhook it and use the rope to tie up with if needed. Tie the rope to the ring with a bowline, improved clinch or uni knot. I also singed the frayed ends of the rope with a flame to prevent further unraveling.

This thing is incredibly sturdy and has tamed my seaghost 130 in my local currents! I can't believe how easy it was to install. I've used several of these, some costing as much as $70 and this trolley is keeping up with them. Thanks for such a deal! EDIT: I have purchased the second one for my son's feelfree lure 11.5. So easy to install that my 10 y/o son was able to install with only my instruction. Can't beat these trolleys!!!!