TP-3: Premium Performance Thermal Pad, 100 x 100 x 1.5 mm, (stackable to 2.0 mm without performance loss), 1 Piece - High Performance, particularly soft, ideal gap filler, bridging gaps

Used one pack of the 0.5mm, 1.5mm and 2mm pads while overhauling my RTX2080. They were all uniformly excellent quality, with the right amount of stickiness and firmness. After the overhauling (including replacing the paste with Arctic MX4) my card went from up to 98 degrees Celsius at max to 87 max (with a higher hotspot). It also took almost all of each of the three packets to replace all the pads; this almost certainly won't be needed unless you are effectively practising like I was but it gives an idea as to the amounts needed. (I did look up the thicknesses on a blueprint for my particular card and had to layer the thicknesses.....which as Arctic say is both east and effective ). Easy to install with patience and a sharp craft knife to cut them and I'm happy with the performance improvement.

Last Time I used thermal paste was back 15 years ago trying to get rid of the red ring of death on Xbox. It was messy and really hard to apply (me being a amateur thermal paste user) to cover the processor in depth and all corners covered. This pad is a game changer its literally this simple. Clean processor with alcohol carefully clean heatsink measure processor cut to fit, take of shiny protective sheet apply to processor and then proceed to take of diamond sheet this one was 1mm thick if you need bigger use two pieces. A complete novice here and this has stopped my pc from throttling this stuff works I have no problems with heat dissipation now. Also there is enough here to reapply many times the size for the price is unbelievable simply because it takes the mess away and makes it easy for novice's like me. Delivered very quick.

Great for Xbox Series X full pad replacement. Thermal conductivity is far superior to the stock thermal putty. Pads can easily be cut to size using a craft knife and are reusable if you are careful with removal. 1.5mm is the correct thickness for Xbox series and Xbox one consoles. Great cost Vs performance. Cannot be used on the APU die itself, only for RAM, VRMs, SSD and expansion card areas. Also available on Amazon is Artic MX-6 which is great for the APU and bottles of isopropyl alcohol 99.9% for thoroughly removing the old paste/putty from all locations.

Used for a PS4 pro refurb. Significantly improved temperatures. Used about half of it, so the pad itself should be big enough to refurb 2 consoles or maybe 3 GPUs. Wouldn't recommend for a modern flagship GPU but an older RTX 20 series or earlier would do fine with this. It's quite awkward to cut cleanly, you really need a sharp blade, not scissors for a good cut. It picks up fingerprints very easily and will deform or even tear under tension but besides that it works exactly as you'd expect - just cut to size and place where it's needed. Be sure to check the thickness, buy the thinnest pad that'll work for your situation, don't try to squash a thicker pad to fit a thinner gap.

good but too expensive

Great product, of course is very brittle as expected so use it very carefully and be prepared using proper tools for it. My PS4 Pro was very loud but after replacing the thermal paste and the pads my console is suddenly very quiet, just whispering. So performance is brilliant. Not too sticky so just beware.

very good product

Happy with my purchase. The thermal pads are very easy to cut into size. Application is simple too. I cut my a piece off for an NVME drive that was slight too long, but it was easy to lift up and cut off the excess. There's plastic tape on both sides which are to be removed. This ensured the pads don't get wasted in storage. I'm getting over 3GB/s with a thunderbolt enclosure using this and it doesn't appear to be running hot.

Die Wärmeleitpads waren sauber und sicher verpackt, alles kam unbeschädigt und ordentlich an. Die Qualität macht einen sehr guten Eindruck, das Material ist sauber verarbeitet und lässt sich gut zuschneiden. Sie sitzen ordentlich, und erfüllen ihren Zweck zuverlässig. Auch der Preis ist für die gebotene Leistung absolut fair. Insgesamt ein solides und empfehlenswertes Produkt.

Thermalpads de calidad, muy bueno si te hace falta cambiarlos en la ram o la tarjeta grafica.

Arctic har aldrig svikit mig förr och denna är inget undantag, grafikkortet (RTX2080) behövde nya och har fått nytt liv igen!

最近のMBに付いているM.2用ヒートシンクパッドと同じくらいの厚みです。

I used this ARCTIC TP-3 1.0mm thermal pad on my MSI RTX 3090 Ti, and it worked exactly as advertised. After installation, I saw a noticeable temperature drop of about 3–5°C, which is impressive for such a simple upgrade. The pad is soft, easy to cut to size, and makes excellent contact without being messy like thermal paste. Another advantage is that it can be stacked up to 2.0mm without performance loss, providing flexibility for various cooling setups. I sold the card after the upgrade, but I was very happy with the performance improvements while I had it. If you’re looking to refresh the thermal pads on your GPU or other components, this is a reliable choice.