HiLetgo 2pcs 5V One Channel Relay Module Relay Switch with OPTO Isolation High Low Level Trigger

Wiring was super intuitive and everything just worked. I was able to power, ground and provide signal all from Arduino and then pull 12V DC from a 4A dedicated power source and connect it directly to the 12V DC magnet when the relay receives a signal. Perfect solution for my secret bookcase door project! Only note was that the relay screws needed the perfect sized screw driver because it felt like it was going to strip with the one little screwdriver I use for everything so I had to get a new small screwdriver kit and then i was able to repeatedly install and change configurations on this board without any problem.

As long as you have a multimeter this is one of the most reliable relay switches I have used. I have it sealed in a large shrink-wrap tube filled with hot glue freely mounted to the side of my bike.

as advertised. great item.

Works well, but it is NOT a bistable/self-latching relay. Requires power for the NO contact to remain closed after engaging the relay (and the opposite for the NC contact). The control line (marked "IN") must be held to the same level as the jumper to keep the relay engaged, i.e. if the jumper is L, IN must be 0V/Ground/Low, if the jumper is H, IN must be 5V/High. Info: 5V relay uses 1ma with relay off and 64ma with relay on. I'll probably find a use for these relays, but I am disappointed that they are not true self-latching relays. I don't know the duty cycle of the relay, but it gets slightly warm after a minute, and I've left it on for at least 10 minutes straight so far with no problem.

I connected the unit to a Raspberry Pi Zero 2W, in order to turn on the 120v main for a UV LED outdoor light project. The DC+ went to the 5v pin (Pin 4) The DC- went to a ground pin (Pin 6) The IN went to GPIO4 (pin 7) The COM went to the Black (HOT) line on the 120v plug. The NO went to the Brown (LOAD) wire on my voltage converter. The 120v Plug's White (Neutral) line is connected to the blue line on the voltage converter. A python script on the Raspberry Pi runs every 5 minutes during the hours between 6pm and midnight via the cron function. The script turns on the converter for 2 minutes and then lets the LEDs cool for 3. Voltage converter link: https://www.amazon.com/dp/B01N5SJ72Y

I need to pulse some fuel injectors off an engine for cleaning and testing purposes so I have this relay connected to an ESP32 and basically just modified the standard 'blink' code to blink really fast. But instead of it blinking an LED directly, it was triggering the relay. I used a small 12V to 5V buck converter scavenged from an old car/lighter phone charger to power the ESP32 and relay from a 12V adapter, then just fed the 12V+ into the COM port of the relay and connected the NO to the load, and voila, every 60ms the relay completes the circuit and fired the injectors just as I needed. The video shows a 12V LED I used for testing, but same principle, and everything worked flawlessly.

Replacement LED backlight strips went out for 2nd time. Decided to stick LED strip lights around the inside instead of replacing again. Only problem is that I had to turn on the strip lights when I turned on TV. Now the light strips turn on when the USB port gets power.

Opens/shuts just like you want with raspi pin out signal, not a huge delay, but not the fastest. Very audible click sound when engaged or disengaged. Screw down wire clamps are very poor quality, you'll have to deal with wires slipping out a lot. After I accidentally shorted 15 amps of 120v AC power through one of these relays, it failed in the closed position, meaning the circuit was stuck active, even when the relay clicked "off." This actually caused me to get shocked, which I didn't find very funny at the time, but my fault for shorting that much power through the relay I suppose. So pair these with a 5 amp fuse to protect them, (and yourself.)

Connected this relay to Shelly Uni to be able to opens my front door remotely. Works really well

No es adecuado a lo que necesito.