Cramer Fugi 5 Kit Grouting & Silicone Profiling & Applicator Tool Kit

Well worth the money, I bought a set 8 years ago and they are now looking well used so ive treated myself to a new set, Expensive but worth it

Got these as have a lot of silicone beading to get sorted out in the house we are fullyu renovating but we first need to sort our Military house that we are leaving soon as a lot of the solicone is knackered and i would rather sort myself knowing its done right that the repair service we get that could have the wrong trade doing it and mucking it up. These worked great and give you a whole type of different beads and sizes you can have and being the brand they are, they are top quality and dont lose their durability so definilty worth getting these over a less a known brand and will be cost effective in the long run.

I held back on buying the kit as i simply couldn't justify spending that amount on a set of plastic assortments for very occasional use. HOWEVER, That said!! This has been one of my best buys so far this year. This makes profiling much easier and produces a nice, professional finish with lots of varying options. The finish is so good and consistent that it beats any sealant finish ive seen done using the "finger method" which also introduces bacteria and compromises the mould protection of your silicone. I particularly liked the little black guides for use on rough/uneven surfaces, also the plastic case is smart and of a sensible design. My kit did not come with instructions but i was able to figure it out with no stress. If you are a pro or keen DIYer just get the kit. Its sturdy and of good quality which should last for many years. An added bonus is that the silicone wipes cleanly off the attachments but you may have to use a tiny pointed screwdriver to remove excess silicon from the crevices. Only snag is that you may use more silicon than the "finger" method so do bear that in mind and get a big paper roll or paper towel to hand Definitely worth your money!!

In all fairness, I wish I had bought a profiling kit like this years ago. They are easy to use. I've used it in 2 rooms and god very good, straight lines. You should know that if your corners are not 90 degrees, the use of the extra plastic legs to stop the spreader from sinking into grout lines is very tricky. My corners were a little under 90 degrees so I had to twist the spreader to keep the lines clean and straight. But this meant I could not use the grout line support legs and ended up with the sealant line sinking into the grout lines at the corners. Which is actually a nice effect, so not too upset. it takes some practice to get right - so practice. The the result is good. Clean up is a bit of kitchen roll - and if you leave the sealant to dry on the spreader, it easily peels off.

These are amazing. I saw them on a you tube film and can’t believe how easy these are to use and what a great result and finish they give. Makes me feel like a right smarty pants

I got put onto this product by my brother and I'm very happy I gave it a go. There are a few good YouTube videos but I'm not sure if I can put the link in. Essentially put all the tools up to the area you want to seal and find the size you want, then cut your nozzle FLAT and NOT angled and cut it to the width of the tool you are using, eg 10mm chamfer, cut it to 10mm width by overlaying the tool on the nozzle. Force the sealant into the joint at right angles moving slowly and the bead will be the correct size for the tool. There are a few things that you must do to get a good finish. If doing a shower do the corner uprights first and leave to bond for 24 hrs before doing the bottom corners otherwise you will end up pulling the upright corner sealant with the tool. If just doing round a sink do the two opposite sides and leave to bond for 24 hrs and then do the center section for the same reason. At no point you should use a soap solution, the tool has release agents impregnated in the rubber and glides effortlessly over the sealant and you wipe the excess off as you go. Using soapy solution hampers adhesion to walls if there is any slight gaps and it goes down including it changes how the sealant is removed using the tool and gives a poor finish. These tools give a consistently excellent professional finish and I highly recommend.

I bought these after watching a few people recommend them on YouTube. I decided to buy a set for all those current and future silicone jobs around the house. A sturdy case with tools that cover a good number of profiles and sizes. The extra 'clip on' pieces are perfect for keeping the tool flat and perpendicular to the surfaces, too. I've used them several times and there are no signs of wear on any of the tools, and they clean up easily with some spirits. Gives a great, neat finish, albeit with some practice. In all, the perfect kit for getting professional results for the home DIYer.

I've tried several different silicone sealant shaper tools in the past, some good, some not so good. This set has been the best I've found so far. They're very easy to use, very easy to clean, and there's a good selection of sizes and shapes, as well as a few useful addition tools for dealing with the uneveness of ceramic tiles (e.g. at the grouted joints). I'm very happy with the results I've achieved with these.

visto su un video youtube, è veramente ben fatto, appena usato per sistemare un bagno dove avevo messo il sigillante acrilico in maniera pessima, ottimo risultato!

Es el segundo que he comprado pues se me pierden algunas piezas; en realidad las dos que suelo utilizar por los ángulos que tienen. Con un poco de paciencia y viendo un par de videos te conviertes en experto y eso que en mi vida lo había utilizado pero me horrorizaba ver como te aplican la silicona en ventanas, baños, etc. Así que decidí aprender y con este kit no necesitas nada más, ni agua, ni jabones, ni historias y quedan rectas y perfectas. Mejor que las que me pusieron de origen en la vivienda.

I'm a experienced Diy'er and I've done a lot of caulking over the years I've always used the wet soapy finger method with pretty good results. After remodeling my kitchen and doing a subway tile backsplash I wanted it to look good so I went to You Tube for some caulking tips. I came across the Fugi kit and figured I would give it a try. Yes it is kinda spendy but after dropping much more on tile I figured it might be worth the cost. I did two separate colors white along the cabinets and grout color in the corners and along the countertops. I primarily used the three blue pieces I didn't find the orange Fugi with the tiles skids helpful my tile is a older style clay tile and pretty uneven. I did lay down a pretty nice caulk edge with the blue Fugi on the 5 setting I found if I leaned it forward I could get over the grout groves and get a nice clean edge. You don't have to get it on one pass I went over it multiple times and even had to add some silicone to some areas. The other blue Fugi tool with the 90 degree edge works fantastic for cleaning up slight lines and excess silicone!! I'm very pleased with the end results and I'm sure I will use the Fugi tools every time I need to caulk something!! The Fugi tools are really easy to clean I used dawn soap and water and they look like new.

Great product just what I wanted. Thanks

Tiene todo lo que se necesita para una aplicación profesional de la silicona, es muy completo. Lo recomiendo.