Go Rhino 3000 Series Center Grill Guard | Mild Steel, Black | 3160B | Fits 2007 - 2013 Chevrolet Avalanche; 2007 - 2014 Chevrolet Suburban 1500 (Excludes Hybrid) & Tahoe

Idk why people say the directions aren’t clear. It was really simple to install. Took me about two hours by myself, would have been less if I didn’t have to watch my kids as well. It’s SUPER sturdy. Looks great. Went to the front of my neighborhood to catch a couple pics and people were looking like “uh oh, unmarked car”. Let somebody cut me off…..PIT MANEUVER. Kidding folk.

Five stars for how sturdy it is.Unit comes unassembled! This was a surprise to me, but i probably didn't read the description.Install was decent by myself. It took about 3 hours total as i couldn't do it at one time.Instructions were dang near useless, but as i didn't expect instructions it helped some.I did install the radiator brackets.It would be a better grill guard if it were welded like a ranch hand.My only issue with the gaurd is the drivers side mounting bracket is funky. It is not so much an issue from go rhino, but they could take the bracket design into consideration.The bolt pattern is the same, but its not mirrored like it should be. Its still a very solid fit, it was annoying. More fault on GM by making it that way to save money.I would definitely buy it again

Installed on a 2008 Suburban:Arrived in 2 days instead of the advertised 7-10. Anyone that gets their hands dirty can install this grill guard. The instructions were adequate, but can be followed. l took off the whole front of the truck to access the frame (youtube made it easy, about 10 minutes to remove) as l had tow hooks already installed and needed those mounts for the guard. l was able to put all the mounting hardware on and finger tighten before putting the front of the truck back on, (be advised, you'll have to tighten the bolts with the front end on, but it's a tight fit for your ratchet with limited swing room. You just need to be able to move mounting brackets slightly when installing the guard. Would recommend tighter than fingertight so the final tightening much easier. Excellent packaging. Looks Fantastic!... can't wait to rear end someone... Total installation time 2.5 hours.

This is a great product. The instructions included in the box are a little awkward and some things are a little difficult to understand. There are plenty of great videos out there that will definitely clear up a lot of the confusion. Installs in about an hour and a half. Best advice I can give for a smooth and easy assembly. Leave every thing hand tight while installing. That way you can level and straighten everything as you tighten everything down.

The guard is very sturdy and fit my 2007 Chevy Tahoe LT. The instructions could have been better. They were in black and white on one piece of paper. I had to watch a couple of videos to learn how to install. Overall worth the price and looks good also. I had it on for about a month now and everything is still good.

Love the new aggressive look. Funny how everyone moves out your way now lol. So the instructions sucks on how to add the push bar on to the suv. The instructions have been photo copied from a poor copy. And it’s not very detailed. You would think so being that there’s like a 100 hardware pieces. That being said. It’s not hard to build. Just take your time. I did it solo. Built the whole thing indoors. Then added all the mounting bracket to the suv. Lastly I bolted the push bar to the brackets. I had lots of washers left over. So I had to go back and add them all where they go. Took about 2 hours total for the whole install.:: UPDATE:: after 3 months the bottom step is rusting from the inside out. The round pipe is raw metal. So any water will rust it. Only way of avoiding this is to seal the ends after install. I called Rhino directly and they offered to send me another step. But it will be raw metal inside again. So I’d have to do the same anyways.

Go-Rhino makes some great stuff, and the 3160B is no exception. It provides a great way to access the rear of the engine bay via the built in step, and a perfect mounting platform for lights, siren speakers, etc via the flat crossmember in the middle. Two sets of pre-drilled holes allow you some flexibility with mounting your equipment (I currently have a set of LED auxiliary lights mounted to it, but they will be moved to a different location once my 30" light bar arrives). The inside edge to edge measurement of the crossmember is just over 34", so you could fit up to a 32" light bar in the space depending on what type of mounting feet it uses. The powdercoating is very high quality, and the included instructions are pretty straightforward if you have some basic knowledge of the underside of your vehicle. All of the necessary hardware was included, and although there were some tight spots to get the ratchet into, everything went together without issue. Great product for the money.

Looks good at first, but within a month it began rusting around the bottom bolts. Tried to contact the manufacturer, but never received a response. Would not buy again if they are unwilling to stand behind their product.