LANSCOERYClear Acrylic Display Case, Assemble 3 Tier Display Box Stand with Black Base, Dustproof Open Door Showcase for Collectibles Memorabilia Figurines (9.4x9.4x11.8inch;24x24x30cm)

Great product for the value. A little wobbly when transporting, but once -placed on a level surface with cover on top, becomes fairly rigid. Peeling the protective coverings was annoying, but the provided glove really helped it not leaving finger prints and maintaining the clarity of the walls. If I had more Funko figures to display, i would def buy again.

This is a fragile case that isn't worthy of valuables. It comes apart constantly. The assembly instructions are terrible, and the video is too. It's too fast and doesn't explain key points to assembly, such as which side is up, which side the hinges should be flush with, inside or out. If you discover the way it's supposed to go by trial and error, it's only after making multiple errors. Every mistake you make ends up breaking a tab. The tabs break easily, and don't fit properly once you do get them in place, and don't hold. Really. Buy something else. It's very expensive on top of all that!

Incomplete assembly instructions and, once figured out, it will NOT stay together.I've even tried super glue. Nothing so far has worked. The slightest touch and it falls like a house of cards.

On time delivery, all pieces fit, plastic is clear with no scratches or hazing. However, the weight of the plastic is much lighter than I'd hoped. The pieces (sides, back, top, bottom) have tabs that fit into slits, but not tightly. Once I had one section assembled it would come apart while trying to fit the next part together. Just a little frustrating, but once I had all but the door loosely together I put a very thin line of super glue along the back and sides of all the shelves, including the bottom, let it sit overnight, and it is holding together nicely now. The door hinges are sturdy, but detract just a bit from the look. This is not a case you want to be opening and closing a lot. Assemble it, fill it, set it on a shelf and forget it. My husband collects classic cars and has models of each. I bought this in which to display those models, and it works for that. And although it seems a bit pricey for the quality, I've ordered a second one for additional models, and will use the two cases until I can afford more expensive, sturdier ones.

The display case arrived on time and was exactly what we needed. I was worried it would be like a plexi glass case, but thank goodness it was a nice clear and sturdy very nice display case. We used it for a display for a variety of our mini donuts. We were able to fit 9-10 mini donuts on each shelf and have some space between them . The case was easy to put together. The door on the back was perfect to slide the donuts in and out. Definitely worth and then some!

I purchased the 12.6x 4x 9.4 case. The item came packaged very well as can be seen in the photos. I didn't give this product five stars because I feel like the price point for this is a bit expensive, I think $25 would be a fair price point for what it is - just plastic panels. I was a bit worried about the panels being too thin because I noticed how flexible they were when I was inspecting them, but once it is put together the exterior structure was pretty solid. However, the middle panels can flex. This would limit the amount of weight I can put on the middle panels. One improvement I would suggest is to lower the tolerance where the panels mate to allow a more secure connection. You can see in one of the photos that the top panel is loose and it takes little effort to lift it up. You would have to be careful when you lift the entire case up as the bottom panel may come off as well. I might consider using Tamiya extra-thin cement glue on all the panels to make sure they don't come loose. Overall, this product is a good one. Just a bit pricey.

This is supposed to hold together? The slots are a few 1/1000" too wide for the tabs that snap into them, so there's no chance anything will hold together. I've never used adhesive on sheet acrylic (Weld-On 4) but I assume it will look pretty shabby when seen through clear plastic.If you have any difficulties with dexterity or spatial construction you'll want to avoid this box. Sheet plastic is typically protected with a liner that must be removed: the black sheets for the base and benches have paper adhered to both sides that will tear easily when peeling off; the clear sheets have a plastic wrap that I could not get started (needed help from someone with stronger nails and more flexible fingers to separate the protective layer, then it's easy to peel off).…The included instruction—actually well written—is for a generic box that is vertical and does not have the stepped benches this kit has, so if you're not comfortable solving spatial puzzles you might flounder.I knew buying this display case that it wasn't attractive, with the tabbed seams shown in the photos, but it looks even worse up close.Very disappointing.

After careful reviewed other customers' reviews, i decided to purchase this display case to house my sons' pinewood derby cars. I was excited when the package arrived today, I was utterly disappointed by the quality and sturdiness after nearly one hour of peeling off the protective films and carefully piecing panels together. Each panel joins adjacent panels with "tongue and groove connectors", but there are not structural strength to keep these joining panels in place. Each of the two interior shelves is connected to three sides only and can't carry any weight of pinewood derby cars.After several failed attempts to keep the displace case stable, I realized that it can't be returned since I already peeled off the protective films. Think twice before you toss $40 out of windows like me. Totally not worth it!!!

This is absolute garbage. It’s so hard to assemble. It doesn’t even stay. You can barely put anything on it without it collapsing. It’s absolute crap…

Parfait pour ma collection de 24 Cuties de Cricut. Ils sont maintenant à l'abris de la poussière et j'ai de la place pour en mettre plus. J'ai mis un Mini dots (autocollant deux faces) sur un pied pour éviter qu'ils bougent. Je vais en commander un autre pour une autre collection.

S’installe facilement pour y inclure des modèles réduits. Cependant, les pièces ne se fixent pas ensemble et il faut faire très attention si on veut déplacer le module pour ne pas que tout se défasse

Je suis très satisfaite

I was super careful with my display box assembly, yet putting the lid piece on the last corner (applying slow and gentle pressure with 1 finger to each corner a bit at a time), and SNAP! It cracked at the corner. Also, the protective plastic film came off of the clear pieces quite easily. The paper-back film on the black pieces was VERY difficult and time consuming to remove, as it would constantly tear like trying to remove a price sticker. Very annoying to assemble because of those two things. Now I am paranoid about opening the top back up to fix something that fell over. (Pen points to crack)