7 Inch Motorcycle Headlight Housing Bracket Headlamp Shell 7" LED Headlight Bucket Mount for Harley Suzuki Chopper Cafe Racer Bobbe Aprilia Matte Black Motorbike Headlight Bucket

Ordered 2 of these bracket/housings. I say 50/50 because 1 of 2 seemed to be used or older hardware that the other. The one that seemed used had silver clips, the rubber grommet it smaller in width, and hard to get both side bolts in. The 2nd had gold clips that were tighter and fit good, rubber grommet fit perfect and was wider, all screws and bolts went in easy. Just weird that got 2 of same thing but they had little differences. Nice product though. Would buy again.

The headlight housing were awesome. Wish they would have worked for my set up. Unfortunately they didn’t. My headlights were too small. That was the reason for returning.

I would give this less than one star if I could. The build quality is terrible and cheap. The rough edges scratched my new headlamp glass while I was trying to fit the light in the housing. The provided clips did not match the terrible instructions. There was no way to secure the light into the housing. Please, learn from me. Spend the few extra dollars and buy a nicer one.

I bought two of these for my two ebikes and installing the headlight was the easy part in my opinion, yes it does not come with instructions, but you use the pins to secure the headlight into the housing (frame) at 4 different points, basically you put one side of the clip in the lip and slide the other end underneath of the lip 12, 3, 6, 9 o'clock positions so it can apply pressure evenly to the headlight, against the headlight housing (frame) thus holding int place. Just YouTube it and you will find videos on how, the only reason I can't give 5 is because one of them came with some scratches up on the outside, and the other one, the screw holes to, "seal" the hosing, on the bottom don't line up so one of my ebike the headlight is not "sealed" evenly across, and one housing is scratched up, But I don't plan on using my ebike in inclement weather so it still meets my needs, and would still recommend to friends if they were looking for a headlight housing for their eBike.

Once i got the light mounted inside, it works perfectly. Easy to mount on bike and easy to adjust. Has a large hole for the wiring so nothing gets pulled or pinched. Looks great.

I didn’t like this motor cycle mount strictly because I mounted it in writing on the road hit a little bump, and the headlight came on mounted rad to grab the wires in the back and hold my light and place at night time it’s not too thick thickness isn’t too great. The fitment seemed a little bit bigger than 7 inches so the light never fit perfectly when light was mounted it was very bright, and the visibility was there but since it would not stay mountain, I had to return

Its a great bucket. Perfect fitting for aftermarket lights, although I did have to cut the rear wire hole larger in order to get all of my plugs to fit. I had to reference the review pictures in order to figure out how to use the clips because there were NO installation instructions. Once I did get them on everything else was a breeze. Great product but be sure to come back and look at others pictures and advice on how to make it easy on yourself.

I am not going to ding this product for the cheap quality because you get what you pay for. I needed something quick and inexpensive so that is what I got. The metal is very thin and the paint is like tissue paper and just as delicate. I ended up putting a new coat of paint when I had to remove it. The tabs that attach the front ring are way too thin and flexible. My bike has a bunch of cables going into my headlight assembly so I had to enlarge the hole and added some vacuum line to protect the cables. My gripe comes from the fact that it does not hold a 5-3/4" light assembly. Even with all the cables, Mt headlight moves all around. You also have no way of adjusting it because there is no positive control of the headlight. I had to shove another piece of vacuum tub. Between the light and housing to keep it in place. I have a Suzuki Volusia so I knew the fork clamps would not fit, but I would not have used them with how thin they are and nothing was included to protect the metal on metal contact. I figured I would have to use my stock bracket so I ended up drilling holes in the housing to use it. It was trial and error getting it to work since that was the only way to adjust where the beam hits. I will be replacing this at my earliest opportunity.

Lights supper bright used it for my motorcycle. Highly recomend and esys plug in and play wireing

Looks good

I thought everyone else leaving reviews was just incompitent, but surely enough i found myself in the same boat. Clips are nearly impossible to get on at first. Folliw the reviewer's picture and give em an upvote for their service. Dont try doing it with your hands or fingers, put one pointy end in first, press the tab part down, then grab the other pointy bit with pliers and push it in with that, youll figurr it out eventually. Overall cool looking bucket

holds the headlight okay, but the bracket to secure the headlight to the forks is garbage. also had to modify the retaining clips to hold the headlight to the shroud. rear housing also came with a dent in it. save your money and buy something higher quality.

So out of the box everything feels ok, brackets mounted to forks ok except full tight they still slide I was lucky enough that they hit a clamp on my forks and stops them sliding down further. I paired with a projector led headlight and it sorta fits loose even with the clips, the hole in the bezel the lights fits through is a touch big. Aside from that it welt together well and looks pretty decent for the price. I’ve seen some people use a piece of rubber under the fork clamps to help and that may have but with my application it worked out good enough