i-Blason iPhone X Screen Protector, Premium 3D Curved Edge Tempered Glass Screen Protector for Apple iPhone X 1-Pack

This is probably one of the best glass screen protectors you can buy for your iPhone X. It is practically invisible compared to the non-3D screen protectors which expose the curved edge. The other 3D ones on amazon that have the individual cutouts for the TrueDepth sensor and camera are more noticeable because you can see the cleared out section. Don't even get me started on the 3D ones that have the "soft edge". Not only does the color not match but you the feel the gap between the glass and the plastic. I would say the only drawback is that the clear portion above the speaker cutout will get some debris overtime which can be easily cleaned by using compressed air from the top edge. Don't bother with the one star review complaining about the bubbles. One thing i-Blason should clarify is that the bubbles will disappear in 1 day (as long as there is no debris underneath). I have installed multiple screen protectors in the past perfectly and my technique is written below. Note: I bought 2 screen protectors however 1 had scuffs on the side. I emailed i-Blason who responded promptly and sent a new placement. Great customer service.Installation steps:1. Make sure to thoroughly clean the surface you are working on as well as your hands.2. Clean the surface on the phone with the included alcohol wipe until there are no smudges.3. Dry off the remaining alcohol with the included microfiber cloth (make sure there is no remaining smudges or marks).4. Use a piece of tape a couple inches wider than the phone and work your way down from the top to the bottom to remove any remaining dust particles. (make sure not to have any blowing vent or fan in the area).5. Install the included installation tray.6. Inspect the phone in different angles to make sure there are no particles left (if there are use the tape method again with the tray).7. Peel of screen protector from backing (always keep sticky side pointed down to prevent any particles from falling).8. Align either the top edge or bottom edge and drop in the screen protector.9. Make sure the speaker hole is aligned (shouldn't be an issues due to the installation tray).10. Push in the center of the screen to allow it to begin sticking.11. Push out from the center to make all the remaining surface stick and remove large air bubbles.12. You might have smaller bubbles around the edges which will disappear over the next day (as long as you don't see a dust particle underneath, if you do lift that edge of the screen use the included dust removal stickers and place back).

I am typically a passive Amazon shopper in the sense I do not typically write any reviews. But because I like the product so much and I see how this product has been unfairly rated, I thought I must step in to say some good things about this product1. Very easy installation. I am usually very afraid of applying my own screen protectors because I usually end up having the screen protector loop sided. The plastic aligner was very fool proof and definitely helped me align the screen protector properly.2. Visually pleasing - really like how the 3D curved edge covers the phone making it not obvious that the phone has a screen protector. My friends who have the same phone but with different screen protectors all liked mine best.Just an input to earlier comments on the bubbles - YES, when you initially apply the screen protector, you will likely see multiple bubbles on it. But be patient, the bubbles will gradually disappear - mine did after 2-3 days of application. The end result of it is worth the wait.

This product came with bubbles already etched into the screen protector itself. So there’s actually bubbles In the adhesive at the top and bottom. On top of that the screen protector never really seals properly so there’s a ton of air bubbles that get trapped underneath no matter how many time you re apply or adjust it there seems to be air bubbles in all four corners. I believe this is because the screen protector isnt actually curved along the edges like the actual screen is so it doesn’t sit properly. Anyway the screen protector itself seems sturdy and is really thick it just sucks that it looks like trash. I’d honestly give it a five star rating if it weren’t for these huge issues with how well it actually applies to the screen.

Not a case friendly screen protector. The black rubber border looks nice , but it hits the case and causes the screen protector to bubble up. The case I have is fairly minimalist, so I am surprised this screen protector is not compatabale

This screen protector is amazing. When you install it it takes a couple of days for some bubbles to disappear if you can survive those 2-3 days you are good to go! I love that it’s flished with the phone so when looking at the phone you can’t tell it has a screen protector at all it doesn’t cut off at the adage of the screen like others do

To be honest I’m a bit bummed. I had originally bought this about a year ago when I first bought my iPhone X and absolutely loved it. Enough that when it broke from dropping my phone I wanted to buy this exact case. Well the 2nd case just came and it has so many air bubbles all around the top layer of the screen that I know for sure weren’t created from me installing it. The air bubbles go right over the front camera so now my camera is hazy and the facial recognition doesn’t work.

It came with all the installation help a person would need in order to do an accurate fit. You can't go wrong with the guide bracket that you install over screen prior to installing the screen protector. After cleaning the phone screen pay close attention and make sure that no lint gets attached to the screen again. Once you lay down the screen protector it will show up.

Screen protector is great! As others have mentioned, the air bubbles do disappear after 24 hours, just need a little patience. Wanted to put in my two cents because I don’t think the low reviews are fair.

The glass is beautiful and covers the complete phone screen Edge 2 Edge. It has got a premium feel and is completely case friendly. I am using uag plyo case.The only reason I am putting a one star is, it has left 2 big bubbles and 1 small bubble. Will wait for 24 hours to see if this goes off. If not have to return this and will order the same item again. As I said before, the glass is very beautiful and may be the one that I got is a defective one. Fingers crossed. See the pic for the bubbles.Update: After 12 hours, the bubbles are all gone. Looking beautiful. See the photo. With UAG plyo case on. 5 star all through now.

Bought a few of these previously. Great protection and the application bracket is awesome.The old version had one hole for the speaker and the problem was try that dust would get in and sit under a thin slot of plastic over the ambient light detector above the speakerThere new design removes the hole and as a notch instead. Not as seamless as the previous version but no dust!

When I received the first one and installed it, three out of the four corners the bubles will not go away. Received a replacement but still the same problem. And I am person where other people are asking me to install there screen protectors because they know how good I am. Don’t waste your money.

Very disappointing. Leaves bubbles around the perimeter and corners. Tried this one over the usual ones that don’t quite cover the complete screen to the edges and will be going back to the usual ones. Good concept, doesn’t deliver.

Absolutely rubbish leaves bubbles all round the side See photo Don’t waste your money Would’ve been good If it fitted properly