DieseRC Wireless Kinetic Light Switch Radio Frequency Safety Switch and 1000W Relay Receiver Controller with Fuse, No Battery Self-generating Switch (1 Way 2 Keys Kit)

Looks great on the wall, switch works perfectly with no need to wire the switch. I've set mine up for an alcove light and also a lamp on a unit on the other side of the room. Easy to fit, you just wire up the light source to the remote switch and it all works fine. I've done a little video to show it working

This was a great find, that I have been very happy with. The product has so far been very reliable, and has enabled me to provide a light switch in our kitchen in a far more accessible location than the wired-in switch, which always seemed to be in the wrong place for how we use the room. Based on the usefulness of this switch set, I've bought several more to use in different rooms around the house.

I bought this to replace a multi-switch stair light setup — one switch downstairs, one upstairs — both in poor locations. This kit let me control both lights from both floors independently and even move the downstairs switch closer to the front door without touching the existing wiring. That alone was a win. After a month of use, everything still works as expected. The build quality is decent — on par with standard (not premium) light switches. No complaints there. 🟡 One issue, though: When both switches are used at the same time (i.e. left and right button on the same unit), only one light usually responds. I spent some time investigating and confirmed it’s not a fault, but a limitation of the tech: The buttons send out short radio bursts, and if both go off simultaneously, the receiver (which I’ve installed inside the ceiling fitting) only picks up one reliably. The fix? Just hit one, then the other — don’t press both at once. It’s a small adjustment, but since this limitation isn’t mentioned anywhere on the product page, I’m docking a star. Overall: very good product, works well, and the included double-sided tape holds the switches firmly in place. Would recommend — just be aware of the quirk.

Works good will buy more

Very happy with this kinetic switch,its doing its job very well for outdoor garden lights. No problems so far and saves having to wire to the switch in timber frame house, so no drilling and breaching the inner wall membrane which could cause problems into the future.

These perform as well as the more expensive units from a national electrical supplier. They work as they should excellent price. Not to bulky for installation

Work as advertised. However feels like its made from very thin, brittle plastic. Will feel very cheap next to a regular light switch.

Does what it says on the tin.

The switch is relatively easy to install. The instruction says to pay attention to connect the phase/neutral correctly to the receiver. For me, it was difficult as the wires didn't fully flow the colour conventions. I had red and brown for zero and phase. In the end, I assumed that phase was the one that was being switched by the original wall switch and it worked just fine (phase was brown for me). The remote switches are a bit loud (I guess due to the charging mechanism as they work without a battery), but the noise is not disturbing. Also sometimes when the switch is pressed too gently they don't turn the lights on. Pressing them again a bit harder makes the difference. The remote switch is a bit slower than the traditional switches. It may take a moment (not too long, like half a second, but noticeable) to turn on the light. The default setting of the remote is what I expect from such a dual-switch system: if you turn the lamp on with one you can turn it off with the other one (or the same one of course). There is also a button on the receiver to set a different logic to the system. My receiver is located in the base of the ceiling lamp. The base is a metal box which doesn't have a top (the top surface is the ceiling itself). The signal can reach the receiver without any issue (the 5 sides of the metal box don't block the signal like a Faraday cage). You will need a voltage detector pen (and potentially some screwdrivers) to set it up. Also, make sure to turn off the main electricity switch. Double-sided tape stripes are provided to glue the switches on the walls.

Aynı markanin ürünlerini bir yıldan uzun bir zamandir kullaniyoruz, hic sorun yasamadik. RF olmasi cok anlamli, bu anahtar pil de gerektirmiyor, kinetik enerjiyle çalışıyor.

No es el primero que he probado, ya lo he hecho anteriormente, funcionan correctamente y especialmente para sitios que no es posible instalar con cable, muy recomendable, seguiré comprando iguales ya que no es necesario cambio de pilas.

Der Funkschalter macht einen sehr wertigen Eindruck, ließ sich sehr einfach installieren und funktioniert tadellos. In meinem Projekt sind beide Empfänger in der ca. 15 m entfernten Garage in Dosen montiert, die Bedienung erfolgt vom Haus aus, also mit zwei Wänden dazwischen. Die beiden Kanäle sind bereits voreingestellt, daher ist keine Programmierung erforderlich. Ich würde ihn sofort wieder einsetzen. Klare Empfehlung!

Facile à pairer, à monter, a marché du premier coup. À voir pour le temps.