

⚡ Ignite your drive with power that sparks envy!
The Pertronix 40511 Flame-Thrower Ignition Coil delivers a robust 40,000 volts at 3 Ohms, designed for universal fit across cars, trucks, and boats. Its sleek black finish complements engine aesthetics while providing enhanced ignition performance, smoother throttle response, and improved fuel economy. Engineered for easy installation and compatibility with Pertronix Ignitor kits, this coil is a must-have upgrade for professionals seeking reliable, high-voltage ignition power.



















| ASIN | B00199BO4C |
| Automotive Fit Type | Universal Fit |
| Best Sellers Rank | #17,988 in Automotive ( See Top 100 in Automotive ) #13 in Automotive Replacement Ignition Coils |
| Brand | Pertronix |
| Connector Gender | Female |
| Customer Reviews | 4.7 4.7 out of 5 stars (1,441) |
| Date First Available | September 14, 2004 |
| Exterior | Smooth |
| Global Trade Identification Number | 00694342004897 |
| Installation Type | Plug Gaps |
| Is Discontinued By Manufacturer | No |
| Item Weight | 1.52 pounds |
| Item model number | 40511 |
| Manufacturer | Pertronix |
| Manufacturer Part Number | 40511 |
| Model | PerTronix |
| OEM Part Number | 40511 |
| UPC | 694342004897 |
| Vehicle Service Type | Boat, Car, Truck, classic |
P**L
Works. Easy install.
Anyone can install this, takes 5 minutes and is super easy. 2 nuts taken off, wires attached, nuts screwed on, plug pushed in. Once installed it will just work in the background, never needing to be messed with again. Required with some aftermarket distributors. Make sure you get the right ohm. Downside - Requires ballast resistors removed or your car wont want to start. That can be tougher than you think depending on your car. My ignition wire was a ballast resistor wire and I had to replace the whole wire from key to engine bay, not an easy task for a rear engined car. Had to go under the glued down carpet, then through the doublewalled firewall. Most cars probably dont have to worry about this, but if yours does be prepared.
S**I
Good quality
Worked as it should.
M**L
Love it
Worked well, was less expensive and faster then the other stores I get tractor parts from
A**.
Works quite well.
This coil was recommended for installation of PerTronix HEI. Word of note: When installing the PerTronix HEI system in the distributor , measure the height of the rotor from the rotor point of contact, to the distributor plate BEFORE removing the distributor plate with the points. Some after market point sets have a rotor that will measure a little taller than OEM. The magnet that mounts on the distributor bumps will make an aftermarket rotor sit .060 higher inside the distributor cap, thus internally destroying the cap. Measure the height of the rotor AGAIN after installing the PerTronix HEI system !! The engine in my boat has never run THIS GOOD! Drove the boat 36 miles up the Missouri River, and 36 miles back. That's 72 miles round trip on a river, without one single hiccup. Great product.
E**D
3 Ohm for Flamethrower
Purchased for a four cylinder Pertronix distributor. Lower OHM coil will work, but shirtens life of pick up.
R**N
Perfect
Worked great. Zero issues.
A**N
Great quality. Well Packaged.
Great coil. I use on 1955 235 inline Thriftmaster engine.
B**B
Great
Great
B**Z
Cumplió todas mis expectativas, es increíble como mejoro la ignición de mi VW sedan 1990, la chispa que genera es excelente, gracias
J**R
excelente
M**L
Llego súper rápido, bien protegido y en excelente estado.
B**Y
Conforme à mes attentes, la voiture démarre au quart de tour maintenant !
M**K
Made a definite improvement to idle and engine appears more fuel efficient.
Trustpilot
1 week ago
1 month ago